View and Download Boss GT-6B owner’s manual online. Boss Owner’s Manual Bass Effects Processor GT-6B. GT-6B Music Pedal pdf manual download. View and Download Boss GT-6B owner’s manual online. Bass Effects Processor. GT-6B Recording Equipment pdf manual download. owning one myself, i can say that the GT-6b was just more wasted . but the 6B’s manual with be the make it or break it point because I’m not.
|Published (Last):||4 November 2013|
|PDF File Size:||1.55 Mb|
|ePub File Size:||17.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
Before using this unit, carefully read the sections entitled: Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. Do not drop it! Device From the GT-6B Panel Descriptions Front Panel fig. The left display shows the bank number. The right display indicates patch names, parameters, and a variety of other information. Press to select parameters. Connect to amps, mixers, or other such devices.
The volume increases as the knob is turned to the right. The distortion gets stronger as the knob is turned to the right. The names of effects that can be controlled with these pedals appear in the lower row of the display. Each effect in the GT-6B has some available quick settings. You can easily create new effect sounds, without having to make any detailed adjustments, just by selecting and combining these Quick Settings.
The content of the display changes, and the GT-6B is ready for a patch to be specified as the save destination. The GT- 6B provides nine types of distortion with two different custom settings. Overdrive This provides the warm, natural type of distortion that occurs naturally when you turn up the volume on a tube amp.
CHORUS This is an effect that adds a slightly detuned sound to the original bass sound, resulting in a beautiful sound with greater depth and breadth.
Developed by BOSS, this is one effect that is popular the world over. Delay Time Fine Makes fine adjustments in units of 1 ms to the delay time. Middle Adjusts the tone of the midrange. Selects the wah effect function. Pedal Wah The Expression pedal is used for real-time control of the wah effect. Rate This selects the auto wah cycle. This makes it easy to achieve effect sound settings that match the tempo of the song synchronizing the cycle to one-half or one-fourth of the BPM when the set cycle rate is increased.
The more the value is increased, the more softly you can gg6b and still have the effect applied. Freq Bosss Sets the frequency range bos the enhanced sound.
Mix Level Adjusts the amount of enhanced sound added to the mix.
Boss GT-6B Manuals
FX-2 With FX-2, you can select the effect to be used from the following. Although it resembles the phaser effect, the flanger yields a colder, more metallic twisting effect. Feedback This adjusts the feedback amount of the harmonist sound. Level This adjusts the volume of the harmonist sound. This specifies the key of the song you are playing.
By specifying the key, you can create harmonies that fit the key of the song. Chapter 4 The Effects Explained Mono: This mode is for the input of individual notes. Select this setting when you want to obtain a pedal bend effect using an external expression pedal. Lo PreDly Low Pre Delay Adjusts the time from when the direct sound in the lower range is output until the effect sound is output. Extending the pre-delay produces the sensation of multiple sounds being played doubling effect.
Lo Level Low Level Adjusts the volume of the lower range. Chapter 4 The Effects Explained 4. Vibrato The vibrato effect is created by slightly modulating the pitch.
Waveform shaping outputs a soft sound with no attack. Octave Shift with Square and Saw This outputs sound one octave below the original sound. Noise Suppressor This effect reduces the noise and hum picked up by the bass. Use this when noise that occurs when you are not playing the bass becomes noticeable.
Since it suppresses the noise by monitoring the volume level of the actual bass sound being input, it always gives a natural effect.
Changing the parameter simultaneously while using different sources may result in noise being generated. Switch the settings as needed to accommodate your setup. Normal The normal state boes Off minimum valuewith the switch On maximum value only while the foot switch is depressed.
Note that carrying out the following procedures erases the recording. Set the switch to this position when recording in stereo or sending stereo signals to a PA. You can set the standard pitch on the GT-6B to frequencies from to Hz.
If this occurs, adjust the display contrast. When you switch banks, the indicator for number pedal last pressed before pressing the Bos pedal flashes, and the GT-6B is ready for the patch number to be specified the patch cannot yet be bozs in this condition. Press a number pedal to select the patch you want to use. If the expression pedal is operated, and that information is transmitted to the GT-6B, the volume changes in accordance with the movement of the pedal.
Setting the Knob Functions Knob Mode This sets the way the values of settings are changed when the control knobs are turned. Turning the knobs ft6b changes the values.
Boss GT-6B Owner’s Manual
Operating From the GT-6B Set them as needed, depending on the intended use. Program Change messages are not output, even when patches are switched. This connector transmits messages from this device. Exclusive messages can be employed to save the settings for effects programs into a sequencer, or for transferring such data to another GT-6B. The two instruments must be set to the same device ID numbers when exchanging SysEx messages.
Appendices Troubleshooting If there is no sound, or if the GT-6B does not function as you expect, first check the following points. If the measures in this checklist do not resolve your problem, you manyal contact your dealer or the nearest Roland Service Bkss. Do the MIDI channel settings of both devices match? Make sure that the MIDI channels on both devices match p. If sending messages from the GT-6B, have you set the settings necessary for sending data?
Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Page of 84 Go. Flanger Bows 37 – P.
BOSS GT-6B SM Service Manual download, schematics, eeprom, repair info for electronics experts
Pitch Shifter Page 38 – PB: Page 59 – Checking the Effect Output Level with th Thank you, and congratulations on amnual choice of the BOSS. Before using this unit, carefully read the sections entitled:. These sections provide important information concerning. Additionally, in order to feel g6b that you have gained a. Owner’s manual should be read in its entirety. No part of this publication may be reproduced in any form.
Table of Contents Add to my manuals Add. Roland pw music keyboard-accessory: Page 10 Press to select parameters.
Boss GT-6B Manuals
Rear Panel Rear Panel fig. Creating You Own Favorite Tones patches p. Adding And Omitting Effects 4.
Ring Modulator Ring Modulator fig. Chorus CHORUS This is an effect that adds a slightly detuned sound to the original bass sound, resulting in a beautiful sound with greater depth and breadth. Band Parametric Eq Selects the wah effect function. Fx-1 Rate This selects the auto wah cycle. Pitch Shifter Feedback This adjusts the feedback amount of the harmonist sound.
Making The Parameter Settings Changing the parameter simultaneously while using different sources may result in noise being generated. Page 50 FS-5U is used. Setting “expression Mwnual Hold If the expression pedal is operated, and that information is transmitted to bosw GT-6B, the volume changes in accordance with the movement of the pedal.
Appendices This connector transmits messages from this device. About The Midi Implementation Exclusive messages can be employed to save the settings for effects programs into a sequencer, or for transferring such data to another GT-6B. Troubleshooting Appendices Troubleshooting If there is no sound, or if the GT-6B does not function as you expect, first check the following points.
Index Index Numerics 12Stage