Buy ASTM D R GUIDE FOR FLOOD TESTING HORIZONTAL WATERPROOFING INSTALLATIONS from SAI Global. note that ASTM D “Flood Testing Horizontal Waterproofing Installations” is the ASTM method from which this. Technical Data Sheet draws. ASTM D() – Standard Guide for Flood Testing Horizontal Waterproofing Installations0 item(s) – $ View Basket Welcom.
|Published (Last):||13 February 2005|
|PDF File Size:||6.57 Mb|
|ePub File Size:||7.39 Mb|
|Price:||Free* [*Free Regsitration Required]|
Overflows are provided in the containment assemblies, when needed, at 5 inches above low point on the test surface so as not to exceed the structural capacity of the substrate. D Terminology Relating to Roofing and Waterproofing. If the asmt does not meet the performance criteria, additional remediation may be required to pass. Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. Lateral loads will be imposed on curbs or walls used for containment of the water during the test procedures and their effect should be accounted for. d595
Standard Guide for Flood Testing Horizontal Waterproofing Installations
Water height is maintained so as not to exceed a minimum level of 2 inches below the edge of flashings. The effects shall be analyzed by a licensed structural engineer prior to placement of additional loads. Historical Version s – view previous versions of standard. Following the completion of the repairs and curing of materials, the area is retested under the same conditions as the initial flood test.
Assurance Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. Formally confirming that your products and services meet all trusted external and internal standards.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. If leakage is detected during the test period, water is immediately drained from the test area. The effects d59957 equipment, planters, or other movable objects present within the test area should be considered. Test area is flooded with water to achieve a minimum cover of 1 inch but not exceed a maximum depth of 4 inches at the lowest point.
Waterproofing membrane and flashings should be inspected and deficiencies repaired. Astn locations shall be monitored during the duration of the test period. See also ACI Containment assemblies are composed of a asttm sheet or a polyethylene sheet adhered to the surface of the waterproofing membrane using a watertight seal duct tape.
Note 2 — Increasing asgm amount of water forming a hydrostatic head beyond mm 4 in. Applicable waterproofing membrane installations that may be tested using this guide are fully adhered or bonded sheet membranes, liquid or fluid applied membranes, or loose dd5957 sheet membranes. If a protection layer is required for flood tested, the recommended practice is that a temporary protection layer be loose laid and removed prior to testing of the waterproofing system.
ASTM D – 98 Standard Guide for Flood Testing Horizontal Waterproofing Installations
Validating the specifications, value and safety of your raw materials, products and assets. Applies for fully adhered or bonded sheet membranes, liquid or fluid applied membranes or loose laid sheet membranes of waterproofing installed on parking garages and plaza deck types over habitable spaces or on elevated structures. Global Reach Intertek is the industry leader with over 42, people in 1, asgm in over countries.
Whether your business is local or global, we can ensure your products meet quality, health, environmental, safety, and social accountability standards for virtually any market around the world. It is the responsibility of the user of this standard to establish appropriate safety and health practices and f5957 the applicability of regulatory limitations prior to use.
Ponded water can freeze and become adhered to the waterproofing system resulting in pulling or tearing of the flashings away from the substrate or may break interior corners. Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
A containment assembly is constructed to be nondestructive, non-penetrating of the waterproofing installation and easily removable. Testing should occur prior to the installation of drainage layer, protection layer, pavers or overburden. Assurance Testing Inspection Certification. Link to Active This link will always route to the current Active version of the standard. Testing is performed for a minimum of 24 hours and maximum of 72 hours when rainfall is not forecasted to occur.
Certification Formally confirming that your products and v5957 meet all trusted external and internal standards.
This standard is not intended for use on building roofing systems. Flood testing ashm considered to be completed if no leaks are identified to have occurred during the test period and the membrane and flashings are intact. Work Item s – proposed revisions of this standard. Need help or have a question?
Inspection Validating the specifications, value and safety of your raw materials, products and assets. The values given in parentheses are for information only. Auditing Consulting Sourcing Training. Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world.